#include "FastLED.h" // 此示例程序需要使用FastLED库
#define NUM_LEDS 60 // LED灯珠数量
#define LED_DT 5 // Arduino输出控制信号引脚
#define LED_TYPE WS2812 // LED灯带型号
#define COLOR_ORDER GRB // RGB灯珠中红色、绿色、蓝色LED的排列顺序int yaliPin = A0; // A0 接口 压力传感器
#include
float t1;
float t2 = 0;
int read5; //敲击端口为7
const int t3 = 300;
int yaliReading;
int yaliPin = 2; //压力开关
int qingxiePin = A5;
int qingxieval ; //倾斜
int attachPin = 3; //触摸
int num = 0;
//int qiaojipin = 9;
// LED on arduino
int huoerdigitalPin = 6; // linear Hall magnetic sensor digital interface
// linear Hall magnetic sensor analog interface 霍尔传感器
bool huoerdigitalVal; // digital readings
//int huoeranalogVal; // analog readings
int qingxie;
//int x = 1; //触摸传感器的int
int y = 1;
int mixflag = 0;
char B;
char C;
char D;
char E;
char F;
char G;
char H;
//char state ;
char mystate;
char hisstate;
char col;
//定义七种颜色状态
//int A[4][3]={{255,250,250},{255,69,0},{255,140,0},{135,206,255}};
bool sta; //触摸状态
void use() {
sta++; //触摸状态
}
SoftwareSerial BT(10, 11); //Pin10为RX，接HC05的TX针脚 //Pin11为TX，接HC05的RX针脚
char val;
char mix;
uint8_t max_bright = 128; // LED亮度控制变量，可使用数值为 0 ～ 255， 数值越大则光带亮度越高
CRGB leds[NUM_LEDS]; // 建立光带leds
void setup() {
//pinMode(qiaojipin, INPUT);
pinMode(9, INPUT);
pinMode(7, INPUT);
pinMode(yaliPin, INPUT); //压力
pinMode (huoerdigitalPin, INPUT); //霍尔
pinMode(attachPin, INPUT); //触摸
attachInterrupt(1, use, RISING);
LEDS.addLeds(leds, NUM_LEDS); // 初始化光带
FastLED.setBrightness(max_bright); // 设置光带亮度
Serial.begin(38400); //蓝牙
Serial.println("Buletooth is ready!");
BT.begin(38400);
co(y);// HC-05默认，38400
}
void co(int x) {
if (x == 1) {
fill_solid(leds, 60, CRGB::Black);
FastLED.show();
mystate = 'A';
delay(50);
} // 更新LED色彩
else if (x == 2) {
fill_solid(leds, 60, CRGB (238, 99, 99));
FastLED.show();
mystate = 'B';
delay(50);
}
else if (x == 3) {
fill_solid(leds, 60, CRGB (139, 101, 8)) ;
FastLED.show();
mystate = 'C';
delay(50);
}
else if (x == 4) {
fill_solid(leds, 60, CRGB (135, 206, 255));
FastLED.show();
mystate = 'D';
delay(50);
}
else if (x == 5) {
fill_solid(leds, 60, CRGB (0, 255, 127)) ;
FastLED.show();
mystate = 'E';
delay(50);
}
else if (x == 6) {
fill_solid(leds, 60, CRGB (147, 112, 219)) ;
FastLED.show();
mystate = 'F';
delay(50);
}
else if (x == 7) {
fill_solid(leds, 60, CRGB (255, 255, 255)) ;
FastLED.show();
mystate = 'G';
delay(50);
}
else if (x == 8) {
fill_solid(leds, 60, CRGB (255, 69, 0)) ;
FastLED.show();
mystate = 'H';
delay(50);
}
}
void color()
{ int c;
if (mystate == 'B') {
c = 2;
co(c);
delay(50);
}
else if (mystate == 'C') {
c = 3;
co(c);
delay(50);
}
else if (mystate == 'D') {
c = 4;
co(c);
delay(50);
}
else if (mystate == 'E') {
c = 5;
co(c);
delay(50);
}
else if (mystate == 'F') {
c = 6;
co(c);
delay(50);
}
else if (mystate == 'G') {
c = 7;
co(c);
delay(50);
}
else if (mystate == 'H') {
c = 8;
co(c);
delay(50);
}
/* else if (mystate == 'A') {
fill_solid(leds, 60, CRGB::Black);
FastLED.show();
y = 9;
}*/
}
void mixcolor()
{ if ((hisstate == 'C') && (mystate == 'B'))
{ fill_solid(leds, 30, CRGB (139, 101, 8) );
FastLED.show();
fill_solid(leds + 30, 30, CRGB (238, 99, 99) );
FastLED.show();
mix = 'H';
delay(50);
}
else if (((hisstate == 'B') && (mystate == 'C')))
{ fill_solid(leds , 30, CRGB (238, 99, 99) );
FastLED.show();
fill_solid(leds + 30, 30, CRGB (139, 101, 8) );
FastLED.show();
mix = 'H';
delay(50);
}
else if ((hisstate == 'D') && (mystate == 'C'))
{ fill_solid(leds, 30, CRGB (135, 206, 255) );
FastLED.show();
fill_solid(leds + 30, 30, CRGB (139, 101, 8) );
FastLED.show();
mix = 'E';
delay(50);
}
else if ((hisstate == 'C') && (mystate == 'D'))
{ fill_solid(leds , 30, CRGB (139, 101, 8) );
FastLED.show();
fill_solid(leds + 30, 30, CRGB (135, 206, 255) );
FastLED.show();
mix = 'E';
delay(50);
}
else if ((hisstate == 'D') && (mystate == 'B'))
{ fill_solid(leds, 30, CRGB (135, 206, 255) );
FastLED.show();
fill_solid(leds + 30, 30, CRGB (238, 99, 99) );
FastLED.show();
mix = 'E';
delay(50);
}
else if ((hisstate == 'B') && (mystate == 'D'))
{ fill_solid(leds , 30, CRGB (238, 99, 99) );
FastLED.show();
fill_solid(leds , 30, CRGB (135, 206, 255) );
FastLED.show();
mix = 'E';
delay(50);
}
else if ((hisstate == 'B') && (mystate == 'E'))
{ fill_solid(leds, 30, CRGB (238, 99, 99));
FastLED.show();
fill_solid(leds + 30, 30, CRGB (0, 255, 127) );
FastLED.show();
mix = 'F';
delay(50);
}
else if ((hisstate == 'E') && (mystate == 'B'))
{ fill_solid(leds, 30, CRGB (0, 255, 127));
FastLED.show();
fill_solid(leds + 30, 30, CRGB (238, 99, 99) );
FastLED.show();
mix = 'F';
delay(50);
}
else if ((hisstate == 'B') && (mystate == 'F'))
{ fill_solid(leds, 30, CRGB (238, 99, 99) );
FastLED.show();
fill_solid(leds + 30, 30, CRGB (147, 112, 219) );
FastLED.show();
mix = 'G';
delay(50);
}
else if ((hisstate == 'F') && (mystate == 'B'))
{ fill_solid(leds, 30, CRGB (147, 112, 219));
FastLED.show();
fill_solid(leds + 30, 30, CRGB (238, 99, 99));
FastLED.show();
mix = 'G';
delay(50);
}
else if ((hisstate == 'B') && (mystate == 'H'))
{ fill_solid(leds, 30, CRGB (238, 99, 99) );
FastLED.show();
fill_solid(leds + 30, 30, CRGB (255, 69, 0) );
FastLED.show();
mix = 'F';
delay(50);
}
else if ((hisstate == 'H') && (mystate == 'B'))
{ fill_solid(leds, 30, CRGB (255, 69, 0) );
FastLED.show();
fill_solid(leds + 30, 30, CRGB(238, 99, 99) );
FastLED.show();
mix = 'F';
delay(50);
}
else if ((hisstate == 'E') && (mystate == 'C'))
{ fill_solid(leds, 30, CRGB (0, 255, 127) );
FastLED.show();
fill_solid(leds + 30, 30, CRGB (139, 101, 8) );
FastLED.show();
mix = 'F';
delay(50);
}
else if ((hisstate == 'C') && (mystate == 'E'))
{ fill_solid(leds, 30, CRGB (139, 101, 8) );
FastLED.show();
fill_solid(leds + 30, 30, CRGB (0, 255, 127) );
FastLED.show();
mix = 'F';
delay(50);
}
else if ((hisstate == 'C') && (mystate == 'F'))
{ fill_solid(leds, 30, CRGB (139, 101, 8) );
FastLED.show();
fill_solid(leds + 30, 30, CRGB (147, 112, 219));
FastLED.show();
mix = 'G';
delay(50);
}
else if ((hisstate == 'F') && (mystate == 'C'))
{ fill_solid(leds, 30, CRGB (147, 112, 219) );
FastLED.show();
fill_solid(leds + 30, 30, CRGB (139, 101, 8));
FastLED.show();
mix = 'G';
delay(50);
}
else if ((hisstate = 'C') && (mystate = 'H'))
{ fill_solid(leds, 30, CRGB (139, 101, 8) );
FastLED.show();
fill_solid(leds + 30, 30, CRGB (255, 69, 0) );
FastLED.show();
mix = 'F';
delay(50);
}
else if ((hisstate = 'H') && (mystate = 'C'))
{ fill_solid(leds, 30, CRGB (255, 69, 0) );
FastLED.show();
fill_solid(leds + 30, 30, CRGB (139, 101, 8) );
FastLED.show();
mix = 'F';
delay(50);
}
else if ((hisstate == 'D') && (mystate == 'E'))
{ fill_solid(leds, 30, CRGB (135, 206, 255) );
FastLED.show();
fill_solid(leds + 30, 30, CRGB(0, 255, 127) );
FastLED.show();
mix = 'F';
delay(50);
}
else if ((hisstate == 'E') && (mystate == 'D'))
{ fill_solid(leds, 30, CRGB (0, 255, 127) );
FastLED.show();
fill_solid(leds + 30, 30, CRGB(135, 206, 255) );
FastLED.show();
mix = 'F';
delay(50);
}
else if ((hisstate = 'F') && (mystate = 'D'))
{ fill_solid(leds, 30, CRGB (147, 112, 219) );
FastLED.show();
fill_solid(leds + 30, 30, CRGB(135, 206, 255) );
FastLED.show();
mix = 'G';
delay(50);
}
else if ((hisstate = 'D') && (mystate = 'F'))
{ fill_solid(leds, 30, CRGB (135, 206, 255) );
FastLED.show();
fill_solid(leds + 30, 30, CRGB(147, 112, 219) );
FastLED.show();
mix = 'G';
delay(50);
}
else if ((hisstate == 'F') && (mystate == 'E'))
{ fill_solid(leds, 30, CRGB (147, 112, 219) );
FastLED.show();
fill_solid(leds + 30, 30, CRGB (0, 255, 127) );
FastLED.show();
mix = 'G';
delay(50);
}
else if ((hisstate == 'E') && (mystate == 'F'))
{ fill_solid(leds, 30, CRGB (0, 255, 127) );
FastLED.show();
fill_solid(leds + 30, 30, CRGB (147, 112, 219) );
FastLED.show();
mix = 'G';
delay(50);
}
delay(5000);
/*read9 = digitalRead(9);
if (read9 != 1)*/
mystate = mix;
color();
mixflag = 1;
}
void loop() {
t1 = millis() - t2;
if (t1 >= t3)
{
t2 = t2 + t3;
//触摸
sta = digitalRead(3);
if (sta != 0) { //触摸信号在哪里读取？
sta = 0;
y++;
if (y > 4) {
y = 1; //点四次以后再变暗无法实现，第四次短暂变暗再次变为桃色
}
co(y);
delay(100);
}
//压力
yaliReading = digitalRead(yaliPin);
Serial.print("yali:");
Serial.println(yaliReading);
//霍尔
huoerdigitalVal = digitalRead(huoerdigitalPin) ;
//倾斜
{ qingxie = analogRead(qingxiePin);
Serial.print("qingxie:");
Serial.println(qingxie);
delay(1000);
}
if (y != 1 )
{
if ( (huoerdigitalVal != 1 ) ) // 同化中上面的 下传上(接收）同化中上面的酒
{
if (BT.available())
{
hisstate = BT.read();
Serial.print("同化上");
Serial.println( hisstate);
}
mystate = hisstate;
color();
}
else {
if ((yaliReading == HIGH))
{
if (qingxie > 600)
{
if (mixflag == 0)
{
if (BT.available())
{ hisstate = BT.read(); //上面的瓶子
Serial.print("混色上");
Serial.println(mystate);
mixcolor();
}
}
}
else
{
BT.write(mystate);
Serial.print("下");
Serial.println(mystate);
//下面的瓶子
}
}
else {
mixflag = 0;
}
read5 = digitalRead(7);
Serial.println(read5);
if ( read5 != 1)
{ y = 1;
co(y);
}
}
}
}
}